AUTONET TV

Kingwood Service Center Maintenance Tips: The Belt Goes On

All Kingwood service advisors know that without the alternator, the battery will go dead in a few miles.

The serpentine belt may also run the pumps for both the power steering and power brakes. And on many vehicles, the serpentine belt powers the water pump. The water pump circulates coolant through the engine to keep it within normal operating temperatures. (On some vehicles, the water pump is powered by the timing belt instead of the serpentine belt.)

So you can see the serpentine belt does a lot of work. And it if breaks, it affects a lot of systems. That's why your vehicle manufacturer and your service advisor at Kingwood Service Center have recommended that it be changed every so often so that it doesn't fail.

Your friendly and knowledgeable Kingwood Service Center service advisor can perform a visual inspection of the belt to see if it has any cracks that signal the belt could fail soon and will measure the amount of belt material to make sure there is enough.

Your serpentine belt works in tandem with a spring loaded pulley attached to the engine called the tensioner pulley. Its job is to make sure there's a constant tension on the serpentine belt so that it doesn't slip. The spring can become worn and no longer provide the necessary pressure to keep the belt tight. At Kingwood Service Center in Kingwood, we recommend that the tensioner be replaced at the same time as the serpentine belt.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net

Going (Lug) Nuts (Lug Nut Replacement)

Here's a part of your vehicle you probably don't think about much: lug nuts.  They're what fasten your wheels onto your axles.  Pretty important, right? In order to take the wheels off your vehicle to service the brakes, rotate the tires, etc., the lug nuts have to be in good shape so a wrench will grip them tightly. 

Because lug nuts are on your wheels, they are exposed to all the elements of the road (salt, water, grime) and really take a beating. Unfortunately, some manufacturers have made them out of two different metals.  Underneath is the working part of the lug nut, made of steel.  On top is the decorative (the "good looking") part, made out of chrome, stainless steel or aluminum.  After a while, the steel part begins to corrode and expands.  That changes the shape of the outer cap, sometimes rounding off the hexagonal edges and making it hard (if not impossible) to either loosen or tighten the lug nuts since the wrench won't fit any more. 

The reason that's so important is those lug nuts must be functional, especially if you find you have a flat tire somewhere on the road.  If the wheel can't come off to be swapped with a spare, it leaves few options, one of which is your vehicle may have to be towed.  All that for corroded lug nuts!

When you take your vehicle in for service, the technician who works on it keeps an eye on many things, especially if he or she is removing wheels.  It's not unusual for your service advisor to recommend you replace several lug nuts at once since some corrode at a different rate than others. Your repair facility is trying to help you avoid driving a vehicle that has wheels that can't easily be taken off when they need to be.

The good news is there are one-piece lug nuts that don't have the problem the two-piece lug nuts have, so replacing them could eliminate that from happening again any time soon.  And that's not "nuts" at all.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net

H20 No! (Driving Through Standing Water)

In a year marked by unusually heavy flooding in North America, drivers are very aware of the possibility they may find themselves driving where water has come over the road.  It can be a daunting and frightening situation.  Flooding waters can move quickly and unpredictably, so you have to keep your wits about you when you encounter that situation.

Here a sample of one vehicle manufacturer's guidelines on what to do.  First, the vehicle is designed to go through some water, but you must be careful.  Never attempt to drive through water deeper than the bottom of your tires.

You can get out of your vehicle to check the depth of the water, but you can never be sure that you aren't going to drive into a spot where the road has washed away.  You can't see below the surface of the water, and suddenly you could find yourself in a place where the road drops off unexpectedly.  In swift moving storm runoff, your vehicle could literally be floating away with the current, putting your life and those of your passengers in mortal danger. 

Never go more than 5mph/8 km/hr when you drive through standing water.  That minimizes the waves you create.  If you DO find yourself in water that is touching your drivetrain components, that water can damage them.  And if you get water in your engine, it can lock up in seconds and stall.  The potential damage can be catastrophic.

You may have found yourself driving in water deep enough to reach your drivetrain components, and it's essential that you have a technician check the fluids to make sure they haven't been contaminated.  That includes engine oil, transmission and axle.  Driving with fluids contaminated with water can severely damage those components. 

The bottom line is to avoid driving through water at all if you possibly can.  Check your vehicle's owner's manual to see if there are specific guidelines for driving YOUR vehicle in standing water.  It's information that could save your life.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net

Steering You Right (Tie Rod End Replacement)

For drivers, S stands for safety.  And there are three other words that start with S that are all equally important: starting, stopping and steering. For your vehicle to be at its safest, all three functions must be in top shape. 

Steering is one of those things we take for granted.  After all, you turn the wheel and your vehicle changes direction. But sometimes you might notice your steering is a little off.  Maybe you've noticed you turn your wheel slightly and your vehicle doesn't turn. You may feel a little vibration in the wheel that increases when you go faster.  You may hear a little squeak from the wheels when you steer and you may notice your tires aren't wearing evenly.

These are signs that your tie rod ends may be failing. Tie rod ends help connect your vehicle's steering mechanism to the wheels.  They can wear out after you've hit one too many potholes or just from constant use.  They can cause sloppy steering and loose handling, and they should be replaced when they've reached the end of their life span.

If you notice any of these things happening on your vehicle, bring it in to us so a technician can check it out.  There are a couple of different types of steering, recirculating ball steering and the one most of the latest vehicles have, rack and pinion. When we replace your tie rod ends, we will remove and replace the old ones and adjust them to meet your vehicle manufacturer's specifications.

Tie rod ends should often be replaced in pairs, and your vehicle should be aligned afterwards.  Keep your steering working the way it's supposed to, and your vehicle will be sure to steer you right.

Kingwood Service Center
3318 Northpark Dr
Kingwood, TX 77339
(281) 360-7323
http://www.kingwoodservicecenter.net